Doepfer A-112 Sampler / Wavetable Module

The Doepfer A-112 Sampler / Wavetable Module offers itself as a lo-fi retro sampler, and creates strenghts out of its weaknesses. You can use it as a powerfully flanging audio effect or a wavetable VCO.

149,00 € 124,17 €

Наличие: В наличии

Ships Monday, August 21 if ordered in the next 2 days, 13 hours and 5 minutes!


The Doepfer A-112 Sampler / Wavetable Module offers itself as a lo-fi retro sampler, and creates strenghts out of its weaknesses. You can use it as a powerfully flanging audio effect or a wavetable VCO.

Module A-112 is the combination of a voltage controlled 8 Bit Sampler and a wavetable oscillator. On top of it the module is able to generate some special effects. A-112 was designed as an additional sound source with the typical sounds of the early 8 bit samplers and is not comparable with the modern polyphonic MIDI samplers available on the market.

Sampling mode: 8 bit audio resolution, 128kB memory in 2 banks 64kB each (equivalent to 2 seconds of sampling time for each bank with 32 kHz sampling rate), audio input with attenuator, overload display in record mode (gate LED), possibility of MIDI Dump to store sounds in a computer via MIDI, non volatile memory for the 2 samples in the module, manual tune control for adjustment of sampling rate for record and play, CV input (~ 1V/Oct), both manual tune and CV determine the sampling rate respectively the pitch (pitch range is 5 octaves), gate input (not a trigger: the sample starts at the positive edge of the gate signal and is played as long as gate is high or until the end of the sample is reached), manual Gate button, non filtered audio output (thus quantizing noise can be used as an element of the sound intentionally)

Wavetable mode: special appearance of the sampling mode when playing a sample, the audio input is now used as a second control voltage input for moving through the sample in 256 byte wide loops (wavetables). The control voltage required to move through all wavetables applied to the input "Wave CV In" is in the range -2.5V (wavetable 1) ... 0V (wavetable 127) ... +2.5V (wavetable 256) when control "Atten." is set fully clockwise. To achieve the typical wavetable oscillator sounds the sampling memory must contain corresponding wavetable data (e.g. loaded via MIDI dump). These data contain a set of wavetables with different harmonic content (e.g. a filter sweep) to get the typical wavetable sound while moving through the tables via CV. But you may also use a "normal" sample and go through the sample with CV to obtain partially amazing sounds never heard before. You may use for example sampled speech and go with CV through the syllables or speech shreds to get really very extreme sounds. An ideal addition for this feature is the Offset/Attentuator module A-183-2 which can be used to adjust the position of the wavetable (Offset) and the modulation depth (Att.). The corresponding jumper of the A-183-2 has to be set to bipolar offset (as the A-112 requires -2.5V...+2.5V to pass through all 256 wavetables). As modulation source an LFO (A-145, A-146, A-147, A-143-3), ADSR (A-140, A-141, A-142, A-143-1/2) or a random voltage (A-118, A-149-1) may be used. Even a ribbon controller (A-198 or R2M), the Theremin module A-178, the Joystick A-174 or the Wheels module A-174-2 are useful to drive through the wavetables.
Effects: Additionally the module offers - in a way free of charge - some effects like delay, reverse delay, pitch shiftinng or freeze. But it has to be pointed out that due to the 8 bit audio resolution these effects are not comparable to high quality effect units and should be understand as an extra for nothing. The A-112 is not an effects unit !

The sampling time of the A-112 is about 1...30 seconds corresponding to a sampling frequency range of about 60kHz...2kHz (64kB@60kHz ~ 1 s, 64kB@2kHz ~ 30 s)

Technical note: the module uses a battery for the non-volatile storage of the sampling data. Batteries have a limited lifespan and have to be inspected at least every two years. For details please refer to the FAQ page of our website:  Lifespan of rechargeable batteries (used for memory backup)

For more detailed information please look at the English user's manual A112_man.pdf.

DOEPFER A-112 SAMPLEDUMPLOADER :  Programm to transfer A-112 Samples in wavefiles (*.WAV) and revers via MIDI System Exclusive Message. DOS 5.0+ and Windows 95 (in Dos-Window - not guaranteed)

More Information
Category Filter Digital VCO
Width (HP) 10
Depth (mm) 100
Skiff friendly Нет
Stock Text in 7-9 days
Stock Message Н/Д
Order Processing Time Н/Д
Expected In-Stock Date Н/Д
On Pre-Order Until Н/Д
Pre-Order Text Н/Д
Hide Ship Date? Нет
Write Your Own Review
You're reviewing:Doepfer A-112 Sampler / Wavetable Module